Designer Table Runner – A table runner is a great alternate to a tablecloth. What if you have a beautiful new table which you don’t need to hide? With a table runner, then it is possible to dress up your table with no undermining this up. Runners may also help to protect your table from serving dishes that might be somewhat too hot.
Follow this tutorial that is step-by-step, and you may earn a beautiful but easy table runner right away.
What You Will Need
• Focus Fabric that is 12″ x 44″. Focus fabric is the star of all the runner.
• Thread which fits the backing fabric.
• A iron.
• A sewing machine.
• A rotary cutter (optional).
• A cutting board (optional).
Choosing the Fabric
The initial step in any sewing project is selecting the fabrics.
• The focus fabric, the “main attraction” of the runner, needs to be 12 inches wide and approximately 44 inches long. (an inch or so of extra length won’t hurt.) A fabric having a pattern will do the job best.
• select a insulation material which can compliment the focus fabric. Just pick one of these colours from the layout of the focus fabric, and then use this as the financing colour.
Earning the Runner
• Spread the insulation material out on a flat surface. Its side (the side you’ll want folks to view) must be facing up.
• Pin the two pieces of fabric together on their right and left sides, making sure the top and bottom edges are also lined up. Don’t fret about the backing fabric being larger than the focus fabric. It will all make sense in just a small bit.
• Sew the fabric on the pinned sides. Utilize a seam allowance of involving 1/4 and 1/2 of an inch, whichever one you are most comfortable with. After sewing, you will have a fabric tube.
• Switch the fabric tube inside out, so that the “right sides” of the fabrics are facing outside.
• Lay the tube on a flat surface, so that the backing fabric is on the underside, and also the focus fabric is on the top. When you smooth down the fabric, some of the border fabric will be visible over the sides. These will be your own boundaries.
• Arrange the fabrics so that the same amount of border is demonstrating either side. You can use a ruler or tape measure for this step should youn’t believe you can do this by eye.
• Use a iron group on to steam to press on the unfinished runner, then focusing on the seams (the folds) on each side.
• This step isn’t necessary, but it is going to help the runner hold its shape during washing. Try to find the stitch as near the attention fabric as you can.
Finishing the Ends
Now it’s time to complete the 2 finishes (the top and the underside) of the table runner. There are essentially two ways to do this, based on which you like best… and that you find easiest.
• Alternative 1. Fold the edge towards the financing, about 1/4 of an inch. Give the seam a good pressing, and then sew the hem. This is the easiest way to finish off your desk speaker. But if you would like to do something a bit fancier, there is another option.
• Alternative 2. If the edges are ragged or uneven, you may use a rotary cutter to trim them. Then use a zigzag stitch to complete off the borders. In this way, your table runner will be more or less reversible. If you would like to quickly give your table a brand new look (or there’s a stain on the front of the table runner which you don’t want anybody to see) just flip the table speaker over and you are set.
• select a fabric which can hold its shape, like cotton. A cotton-polyester mixture will do the job also. And home décor fabrics make amazing runners.
• Given that table runners are really simple to make, and use so little fabric in contrast to tablecloths, you might have a group of table runners for every season, holiday, or special event. Just pick a couple of themed fabrics to match the event, and you’ll be able to make four or five table runners in one afternoon.
• A single table speaker looks amazing running down the middle of a table. However, four or three matching table runners may appear good running across the width of the table. And, if your table runners are more than your table is broad, that is okay. Just allow the ends of the table runners hang from the sides of the table.