Tablecloths And Table Runners – A table runner is a fantastic alternate to your tablecloth. Imagine if you have a beautiful new table that you don’t wish to conceal? Having a table runner, it is possible to dress up your table with no completely covering it up. Runners may also help to protect your table from functioning dishes which may be a bit too hot.
Stick to this tutorial that is step-by-step, and you may create a lovely but simple table runner very quickly.
What You’ll require
• Focus Fabric that is 12″ x 44″. Focus fabric is the star of your runner.
• Backing Fabric that is 18″ by 44″.
• Thread that matches the backing fabric.
• An iron.
• A sewing machine.
• A ruler or tape measure.
• A cutting board (optional).
Choosing the Fabric
The initial step in any sewing project is choosing the fabrics.
(a inch or so of additional length won’t hurt.) A fabric with a pattern will do the job best.
• pick a backing fabric that can compliment the focus material. Just pick one of these colours from the pattern of their concentration material, and then use that as the backing color.
Making the Runner
• Spread the backing fabric out on a level surface. Its best side (the side you will want people to see) must be facing upwards.
• Put the focus fabric right side down on top of the backing fabric.
• Pin the two pieces of fabric with their left and right sides, making sure the top and bottom edges can also be lined up. Do not worry about the backing fabric being bigger than the concentration material. It will make sense in just a little bit.
• Sew the material on both pinned sides. Utilize a seam allowance of between 1/4 and 1/2 of the inch, whichever one you are comfortable with. After sewing, you will have a fabric tubing.
• Turn the material tubing inside out, in order the “straight sides” of both fabrics are facing outside.
• Put the tubing on a level surface, so the backing fabric is on the bottom, and the concentration fabric is on the surface. When you smooth down the fabric, some of the edge material will be visible over the sides. These will be your own boundaries.
• Arrange the fabrics so the same sum of edge is demonstrating either side. You can use a ruler or tape measure for this particular measure should youn’t believe you’re able to do it by eye.
• Use a iron group on to steam to press the bare runner, focusing on the seams (the folds) to each side. You want the seams to be sharp and crisp.
• This measure isn’t needed, but it will help the runner maintain its shape during washingmachine Attempt to find the stitch as close to the concentration material as you can.
Completing the Ends
Now it is time to finish the 2 ends (the top and the bottom) of your table runner. There are essentially two ways to do so, depending on that you like best… and that you find easiest.
• Option 1. Fold the border to the backing, about 1/4 of the inch. Give the seam a good pressing, sew the hem. This is the simplest way to finish off your table speaker. But, if you would like to do something a little fancier, there is another option.
• Option 2. If the edges are ragged or irregular, you may use a rotary cutter to trim them. This way, your table runner will be less or more reversible. If you want to quickly give a table a new look (or there is a stain on the front part of the table runner that you don’t want everyone to see) just flip the table speaker over and you are set.
More Table Runner Tips
• pick a fabric that can maintain its shape, such as cotton. A cotton-polyester blend will do the job too. And home décor fabrics make amazing runners.
• Given that table runners have been so simple to make, and use so little material in comparison to tablecloths, you may have a group of table runners for each season, holiday, or special event. Just pick a couple of themed fabrics to coordinate with the event, and you’ll be able to make four or three table runners in a single afternoon.
• An individual table speaker looks amazing running down the middle of a table. However, three or four matching table runners are able to appear good running across the breadth of your table. And, in case your table runners are longer than the usual table is wide, that is okay. Just allow the results of the table runners hang from the sides of the table.